| Alarm # | Led Display | Content of FANUC SPINDLE Alarms | |||
|---|---|---|---|---|---|
| 8 | 4 | 2 | 1 | ||
| 1 | o | Motor Overheat | |||
| 2 | o | Speed deviates from commanded speed | |||
| 3 | o | o | Regenerative fault | ||
| 6 | o | o | Excess Motor Speed Analog | ||
| 7 | o | o | o | Excess Motor Speed Digital | |
| 8 | o | Voltage higher than specified | |||
| 9 | o | o | Radiator for power semiconductor overheat | ||
| 10 | o | o | +15Volt Supply is low | ||
| 11 | o | o | o | DC Link voltage is high | |
| 12 | o | o | DC Link current is high | ||
| 13 | o | o | o | CPU and peripheral parts are defective | |
| 14 | o | o | o | ROM is defective | |
Alarm List for the following Drives:
| Alarm # | Led Display | Content of Alarms | |||
|---|---|---|---|---|---|
| 8 | 4 | 2 | 1 | ||
| 1 | o | Motor Overheat | |||
| 2 | o | Speed deviates from commanded speed | |||
| 3 | o | o | Fuse F7in DC link is blown out. | ||
| 4 | o | Fuses F1,F2,F3 for AC input blown out. | |||
| 5 | o | o | Fuses AF2 or AF3 on PCB are blown out. | ||
| 6 | o | o | Excess Motor Speed Analog | ||
| 7 | o | o | o | Excess Motor Speed Digital | |
| 8 | o | Voltage higher than specified (24v) | |||
| 9 | o | o | Radiator for power semiconductor overheat | ||
| 10 | o | o | +15Volt Supply is low | ||
| 11 | o | o | o | DC Link voltage is high | |
| 12 | o | o | DC Link current is high | ||
| 13 | o | o | o | CPU and peripheral parts are defective | |
| 14 | o | o | o | ROM is defective | |
| 15 | o | o | o | o | Option circuit fault. |
Alarm List for the following drives:
| Alarm Display | Alarm Content |
|---|---|
| AL-01 | Motor Overheated |
| AL-02 | Speed deviates from commanded speed |
| AL-03 | Fuse F7in DC link is blown out. |
| AL-04 | Fuses F1,F2,F3 for AC input blown out. |
| AL-06 | Excess Motor Speed Analog |
| AL-07 | Excess Motor Speed Digital |
| AL-08 | Voltage higher than specified (24v) |
| AL-09 | Radiator for power semiconductor overheat |
| AL-10 | +15v power supply is abnormally low |
| AL-11 | DC Link voltage is high |
| AL-12 | DC Link current is high |
| AL-13 | Data memory for CPU abnormal |
| AL-16 | RAM in NVRAM is abnormal |
| AL-17 | ROM in NVRAM is abnormal |
| AL-18 | Check sum alarm of ROM |
| AL-19 | Excessive alarm of U phase current detection circuit offset |
| AL-20 | Excessive alarm of V phase current detection circuit offset |
| AL-21 | Excessive alarm of velocity command circuit offset. |
| AL-22 | Excessive alarm of velocity detection circuit offset. |
| AL-23 | Excessive alarm of ER circuit offset. |
| AL-14 | ROM is abnormal |
| AL-15 | Spindle selection control circuit is abnormal. |
Alarm List for the following drives:
View Fanuc Spindle Amp Alarm Codes for Alpha Series here.
| Alarm # | Meaning |
|---|---|
| AL-01 | Motor Overheat |
| AL-02 | Speed deviates from commanded speed |
| AL-03 | 24v Fuse is blown. (before PCB edition 09A) |
| AL-04 | |
| AL-05 | |
| AL-06 | Excess Motor Speed Analog |
| AL-07 | Excess Motor Speed Digital |
| AL-08 | Over voltage |
| AL-09 | Overheat of radiator |
| AL-10 | Low voltage of input power. |
| AL-11 | Excessive high voltage of DC link |
| AL-12 | Abnormal current of DC link |
| AL-13-15 | |
| AL-16-23 | Defective arithmetic circuit and peripheral circuit |
| No indication | Defective ROM |
Alarm List for the following drives:
| Alarm # | Meaning |
|---|---|
| AL-01 | Motor Overheat |
| AL-02 | Speed deviates from commanded speed |
| AL-03 | 24v Fuse is blown. (before PCB edition 09A) |
| AL-04 | Open phase of input power. |
| AL-05 | |
| AL-06 | Excess Motor Speed Analog |
| AL-07 | Excess Motor Speed Digital |
| AL-08 | Over voltage |
| AL-09 | Overheat of radiator |
| AL-10 | Low voltage of input power. |
| AL-11 | Excessive high voltage of DC link |
| AL-12 | Abnormal current of DC link |
| AL-13 | Defective arithmetic circuit |
| AL-14 | Defective ROM |
| AL-15 | Defective optional circuit. |
| AL-16-23 | Defective arithmetic circuit and peripheral circuit |
| No indication | Defective ROM |
Let MRO help you troubleshoot and repair your spindle amplifier, with our professional repair services! Or, if you need a replacement FANUC part, we have you covered with our extensive selection of FANUC parts.
Arc flash incidents are among the most dangerous hazards in the electrical industry, posing serious…
Understanding an Arc Flash An arc flash stand as one of the most dangerous electrical…
A Distributed Control System (DCS) is a type of automated industrial control system (ICS) used…
The Effects of Dirty Power In today's tech-driven world, many of our most valuable devices…
The game is almost over, and your team is losing. You can feel the crowd’s…
Whether we want to admit it or not, our entire world economy hinges on the…